As there are 300 nozzles on the bottom of capsule(cartridge), if we didn’t use CINOART for a long time, and we use it again, and we find there is no photo on the coffee, we should use napkin to clean the bottom of capsule(cartridge), and it should work well. And if there is some white line o nthe photo, we also can change the print type to solve it as below:1. Go to “Setting Page” and click [Print Type]2. And Click [Middle Speed] or [Low Speed], and start printing again
CINOART get photo by wifi, so if we met the problem that after we sent from cellphone, and CINOART can’t get the photo, it should be the wifi not so good, we can to as below to test. Go to main page and click [WIFI] button access to wifi page. And click [Speed Test] to test the wifi speed, and click [Start] to start testing. If the speed keep 0, it means the wifi is not good, we should connect to other wifi such as hotspot. Restart CINOART.
There are 3 cup sizes for printing, they are B-Cup, M-Cup, S-Cup, if they are not suitable for your cup, you can adjust them as below: Go to “Setting Page” and click [Change Cup Size]. Input the diameter of your cups in millimeters. Click [Confirm] to save it. Notice: In case the printing is out of cup due to the cup is not in the center, the number we input should less than diameter such as [diameter – 5] mm.
After connect WIFI and install capsule, here after we will upload photo. The main steps as below: Go to “setting page”, scan the QRCode on the right-down corner. Access to a webpage, there are three function “Image Library”, “Hand Drawing”, “Upload Image” to send photo. If you choose “Upload Image”, you can choose photo from cellphone. After you choose image, you also can adjust the lightness and contrast of photo by click right-up corner of the webpage. And click send to upload photo. And then click the photo from the screen of CINOART, and start printing. How to save photo in CINOART? If we want to save photo(such as logo) uploaded in CINOART, we just need to long touch the photo for 3 seconds until a lock appear on the right-up corner of the photo, it means this photo has been saved. If we want to remove the saved photo,…
After connect WiFi, we need to install capsule(cartridge) and active it as follows: On the settings page, select the [Change Capsule] button. Go to “Change Capsule Step 1” and enter the capsule code (the uppercase letter of the capsule is encoded at the bottom of the side of capsule). Click [Next] to enter the “ Change Capsule Step 2” and refer to the two pictures on the interface to install the Capsule. Click [Finish], and complete the activation and installation of Capsule.
After removing the protection device for transportation, CINOART and the power adapter can be linked. After booting, the wifi connection is required first. The specific operation is as follows: Click the [wifi] button in the upper right corner of the screen. Enter the wifi page, select the wifi to be connected in the wifi signal list Enter the wifi password in the box and click [OK] Precautions: a. If the wifi has no password and does not perform secondary authentication (that is you need to enter the mobile phone number and other information for authentication), you can directly click the [OK] button to connect to the wifi;b. If the wifi needs to be authenticated twice, you can contact the network administrator to set the mac address of the device (the mac address can be viewed on the wifi interface) to the background whitelist. Wifi connection operation video:
CINOART Coffee Printer adopts the structure of the 3D printer, so it is necessary to fix the internal movable part during transportation. And the coaster is placed in the central groove of the lifting platform in order to place the cup. Two fixed methods are mainly used:1. It is fixed by the strapping tape at the left front of CINOART. Although the method is reliable, it cann’t be reused, and the fixing method is somewhat complicated;2. The threaded rod is fixed on the back of the CINOART. The method is simple and reliable, and can be reused. The specific operation is as follows:a. Remove the threaded rod above the backb. Place the removed threaded rod in the hole below the top hatch Key points: Be sure to fix the internal movable part during transportation to reduce the internal damage by transportation.
In order to facilitate you to learn how to use the CINOART Coffee Printer, we specially organize the teaching videos of CINOART Coffee Printer through this page. You can learn through the following videos: 中文：CINOART 奇诺提咖啡拉花机教学视频目录 CINOART Coffee Printer packing list CINOART Coffee Printer Video – Before Power On(**Important**) CINOART Coffee Printer Video – WiFi Connection CINOART Coffee Printer Video – Install Cartridge CINOART Coffee Printer Video – Upload Photo and Save Photo (**Important**) CINOART Coffee Printer Video – Change Cup Size CINOART Coffee Printer Video – Can’t get the photo(WIFI Speed Test) CINOART Coffee Printer Video – After Printing, There is no photo on the coffee
For CINOART Coffee Printer, the standard items are as follows: coffee printer, cartridge, power adapter, coaster.